How to Properly Install and Use TOS 7 on the 425 Plus Series TNAS

New system installation, system re-install
User avatar
TMzethar
TM Support
Posts: 3110
Joined: 27 Oct 2020, 16:43

Re: How to Properly Install and Use TOS 7 on the 425 Plus Series TNAS

Post by TMzethar »

Moncef wrote: ↑09 Oct 2026, 20:45
Based on the information you provided, as mentioned on the first page of this thread, you will need to update your BIOS first in order to use TOS7 properly.
viewtopic.php?t=10182
To contact our team, please send email to following addresses, remember to replace (at) with @:
Technical team: support(at)terra-master.com (for technical support)
Service team: service(at)terra-master.com (for purchasing, return, replacement, RMA service)
User avatar
Din0
Posts: 10
Joined: 05 Jan 2026, 02:18
Czech Republic

Re: How to Properly Install and Use TOS 7 on the 425 Plus Series TNAS

Post by Din0 »

CursaYang wrote: ↑11 Jul 2026, 08:02
Din0 wrote: ↑10 Jul 2026, 19:59
If you are not using Slot 3, there is no impact, and you can upgrade directly to TOS 7.
Hi CursaYang,

Thanks for the confirmation. I have a general question regarding the BIOS update procedure itself for future reference.

The instructions always state that all drives must be removed before flashing the BIOS. Since removing NVMe drives from the motherboard is quite tedious compared to standard SATA drives, I would like to ask: why is it strictly necessary to remove them?

Is it merely a general safety precaution to protect user data in case of a flash failure, or does having the NVMe drives installed actually interfere with the BIOS flashing process or the subsequent boot/PCIe initialization?

Thanks for explaining!
User avatar
EriChan
TM Support
Posts: 459
Joined: 06 Jan 2026, 12:27
China

Re: How to Properly Install and Use TOS 7 on the 425 Plus Series TNAS

Post by EriChan »

Din0 wrote: ↑02 Nov 2026, 15:54
The requirement mainly comes down to two key points:
  • Ensure a clean boot path: It prevents the NAS from accidentally booting into existing drives or old UEFI entries instead of the USB flasher. Since this BIOS update specifically fixes the Slot 3 NVMe boot priority, keeping NVMe drives installed easily introduces boot variables.
  • Isolate storage devices: Flashing involves controller resets and PCIe/NVMe re-initialization. Removing the drives prevents abnormal disk access, partition table issues, or altered boot entries if an interruption occurs.
In short, it eliminates boot variables and protects your storage integrity.
To contact our team, please send email to following addresses, remember to replace (at) with @

Technical team: support(at)terra-master.com(for technical support)
Service team: service(at)terra-master.com(for purchasing, return, replacement, RMA service)
User avatar
GiGi57
Posts: 1
Joined: 13 Nov 2026, 22:03
France

Re: How to Properly Install and Use TOS 7 on the 425 Plus Series TNAS

Post by GiGi57 »

Hello !
I've just ordered a TerraMaster F2-425 with two harddrives Seagate NAS IronWolf Pro 4 To ST4000NE001 7200 tr/min 256 Mo SATA 3,5 pouces.
I would like to connect the TerraMaster NAS directly on my Internet box with RJ45 Ethernet connexion and access it with the WiFi from the box(I only can connect my PCs to the box with WiFi in my house , no Ethernet connections are able).
Some one could help me to explain how to initialize and configure the TerraMaster at first connexion to be used with WiFi connection??? Thanks a lot at all!!!!!
How can I upgrade it to the last firmware with my WiFi connection ?
Post Reply

Return to “Initialization & Installation”