Page 1 of 1

[Help] Relatively new T9-500 Pro will not boot after clean shutdown from UI

Posted: 13 Nov 2026, 23:40
by plawlor
I also sent an email to support, but now that O365 email is flowing again, I was finally able to register to this Forum...

I received a new Terramaster T9-500 Pro a little over a week ago — purchased through Amazon. Running TOS7 with a single 16 GB stick, 2 x 2TB NVMe, 3 x 18 TB SATA drives. Has been working great until yesterday.

I initiated a shutdown via the UI. Everything seemed to come down clean. Went to power it back up, and there was no response at all from the power button. Tried pressing short, long, multiple times with no response. Unplugged the unit and held the power button for 20+ seconds. Plugged back in and power came on. Fan started on full, but it stops there — no video output to HDMI, no lights on USB keyboard. Nothing. Left it for 15+ minutes — still nothing. Read some articles online and the Terramaster website — tried the following:

1) Removed and reseated RAM stick
2) Removed and reseated RAM stick in other socket
3) Removed all SSD and SATA drives
4) Removed USB boot drive
5) Erased, re-imaged, and reinstalled USB boot drive as per your website's instructions
6) Imaged new USB drive and installed

Between each of the above attempts, my cycle was always the same — press and hold power button until system power turned off; unplug power cord, HDMI, and USB keyboard; press and hold power button for 20+ seconds; plug power, HDMI, and USB keyboard back in. The behaviour is the same for all attempts, even when down to bare metal with just factory RAM stick and USB boot drive installed. System powers on, fan stays full, no video output.

Factory reset procedure does not work either. 3 short beeps never comes.

I would very much like to preserve my Volume1 RAID (across 2 x 2TB NVMe) as it contains 20+ containers running home systems and custom mcp builds, but NVMe #1 also houses the system partition in addition to being part of the VOlume1 RAID.

Is there anything else to try? Or is this an RMA?

Thanks,
Peter

Re: [Help] Relatively new T9-500 Pro will not boot after clean shutdown from UI

Posted: 14 Nov 2026, 09:35
by CursaYang
Thank you for providing such detailed fault information, and thank you as well for the troubleshooting steps you have already tried.

Based on the symptoms so far — the fan running at full speed continuously after the device is powered on, no video output over HDMI, no response from the USB keyboard, and the problem persisting even after removing all drives and re-creating the USB boot drive — we suspect that the device may be encountering an abnormality during BIOS/UEFI initialization or at the motherboard power management stage.

We recommend that you try resetting the BIOS/CMOS settings:

1. Shut down the NAS completely and unplug the power cord.
2. Open the chassis and locate the CMOS battery on the motherboard.
3. Carefully remove the CMOS battery and wait for about 5 minutes.
4. Reinstall the CMOS battery in its original position.
5. Reconnect the power and try to boot the device without any NVMe drives, SATA drives, or USB boot drive installed.
6. Observe whether the HDMI output can display the BIOS startup screen, and whether the keyboard becomes responsive again.

Please note that before performing these steps, make sure the device is fully powered off, and handle the components carefully to avoid damaging the motherboard or other parts.

In addition, considering that your NVMe drives contain important RAID data and a Docker environment, please do not initialize the storage pool, format the drives, or reinstall the system for the time being.

If the device still cannot boot normally after the CMOS reset, please let us know the test results. Since the device was purchased only recently, if the problem is confirmed to persist, we can further assist you in arranging after-sales service.

Thank you for your cooperation and understanding.

Re: [Help] Relatively new T9-500 Pro will not boot after clean shutdown from UI

Posted: 14 Nov 2026, 21:20
by plawlor
Thank you for your response.

Tested the above process this morning. Still no display or life in USB keyboard.

Please advise on next steps.

Re: [Help] Relatively new T9-500 Pro will not boot after clean shutdown from UI

Posted: 14 Nov 2026, 21:52
by CursaYang
Please record a video of the device powering on (without any drives installed) and send it to our technical support email at [support(at)terra-master.com].
Include a link to this post.
Also, please provide your purchase order details.

Re: [Help] Relatively new T9-500 Pro will not boot after clean shutdown from UI

Posted: 14 Nov 2026, 22:29
by plawlor
That information has been sent to support.

Thanks.

Re: [Help] Relatively new T9-500 Pro will not boot after clean shutdown from UI

Posted: 17 Nov 2026, 00:16
by plawlor
Support has been in contact with me re: the RMA process, and the unit has now been shipped back. Thanks for your help.

When I receive my replacement, what initialization steps should I take to retain my current RAID volumes on both the NVMe and SATA drives?

Thanks,
Peter

Re: [Help] Relatively new T9-500 Pro will not boot after clean shutdown from UI

Posted: 17 Nov 2026, 12:53
by EriChan
plawlor wrote: ↑17 Nov 2026, 00:16
Thanks for the update. Once your replacement T9-500 Pro arrives, migrating your existing drives and RAID volumes is straightforward—just make sure the unit is powered off first:

1. Keep the replacement device powered off and do not insert any new or blank drives yet.

2. Reinstall all of your previous drives (both the 2 x 2TB NVMe SSDs and the 3 x 18TB SATA HDDs) into the replacement unit.

3. Power on the NAS.Because all of your system configurations, RAID volumes, and data are stored directly on these drives, the replacement unit will boot directly into your previous system environment and automatically recognize both your NVMe and SATA RAID volumes along with your Docker containers.

Please let us know how everything goes once the replacement unit arrives!

Re: [Help] Relatively new T9-500 Pro will not boot after clean shutdown from UI

Posted: 21 Nov 2026, 04:37
by plawlor
Hi. My replacement unit arrived. Followed your instructions, and everything is back up and running. Nothing lost.

Thank you very much for your help!

Peter