[ Jellyfin ] The Free Software Media System

[m00ndogg]

F2-223 server TOS 5.1.145-00320 I'm trying to upgrade from 10.9.2.0 to 10.10.x.
I don't want to un-install the old version because I don't want to lose all of the settings that took me so long to setup.
Can those settings can be saved some how? ...
Can I just upgrade in-place while keeping the old settings?

[DaveSanto]

You can´t upgrade your current TOS5 10.9.x with the TOS6 10.10.x (please correct me if there is a possibility)
We need to hope on that someone will provide a 10.10.x version which is also available/running on TOS5

PS: I got the same problem that the TOS5 10.9.x is not working anymore for my FireTV Stick, to get an working update on this would be great

[outkastm]

done

[DaveSanto]

Wow, that was really fast - I installed the update, restarted Jellyfin module and that's it - 10.10.2 is running, all custom settings are still there. On the FireTV Stick I had to delete the linked account and add it again because it still recognized the server as 10.9.6 - In addition a message appears that at least version 10.10.3 is required, but works fine after adding the Jellyfin Server with 10.10.2 again.

A BIG THANK YOU!!! to @outkastm from my side for fixing this

[LakesideScott]

I'm having the same issue with my Chromecast dongles. I'm currently running TOS 5.19 with Jellyfin 10.9.6.1. Chromecast says I need at least 10.9.11 if I update the Jellyfin client there (I've turned off auto-updates on Chromecast), so I've downloaded Jellyfin 10.10.2. I just want to make sure I upgrade without losing all the configurations.

All I have to do is stop my current Jellyfin version in TOS, install the new version and start it, correct?

[outkastm]

Config will not be deleted during update.
In any case, you can zip the folder and download to your computer for backup via TOS

[LakesideScott]

OK, thanks!

[LakesideScott]

Just an FYI for anyone reading this post, the ZIP file for my system was a little over 5GB! So it might take a while to download.

[ajkaramba]

I got a TerraMaster F4-423 and hardware transcoding is not working properly.
I run TOS6 with the latest updates, also the FFmpeg51 and Jellyfin is latest updates.

Here are my settings:









The log shows for example (with low power activated):
Stream mapping:
Stream #0:0 -> #0:0 (h264 (native) -> hevc (hevc_qsv))
Stream #0:1 -> #0:1 (copy)
Press [q] to stop, [?] for help
[hevc_qsv @ 0xab06c0] Selected ratecontrol mode is unsupported
[hevc_qsv @ 0xab06c0] some encoding parameters are not supported by the QSV runtime. Please double check the input parameters.
Error initializing output stream 0:0 -- Error while opening encoder for output stream #0:0 - maybe incorrect parameters such as bit_rate, rate, width or height
Conversion failed!

I also tried to deactivate low power settings, this didn't change anything.
Stream mapping:
Stream #0:0 -> #0:0 (h264 (native) -> hevc (hevc_qsv))
Stream #0:1 -> #0:1 (copy)
Press [q] to stop, [?] for help
[hevc_qsv @ 0x12aef00] Selected ratecontrol mode is unsupported
[hevc_qsv @ 0x12aef00] Low power mode is unsupported
[hevc_qsv @ 0x12aef00] some encoding parameters are not supported by the QSV runtime. Please double check the input parameters.
Error initializing output stream 0:0 -- Error while opening encoder for output stream #0:0 - maybe incorrect parameters such as bit_rate, rate, width or height
Conversion failed!

[outkastm]

can you rund these commands in terminal and post the result ?

Code: Select all

dmesg | grep i915