Good morning.
Two apps fundamental in a NAS are Emule (for p2p downloads) and Calibre (The best ebook manager in the world!).
It is possible to implements these two in TOS?
Thank you very much.
Emule and Calibre
Re: Emule and Calibre
eMule is a p2p download application for Windows OS, the org did not release any verison for linux untill now.
F4-221 TOS 5.1.34 (SAMSUNG 250 SSD x1, WD Red 8TB x 1, Single drive)
F2-423 TOS 5.1.34 RAID1(12TB IronWolf x 2)
F2-423 TOS 5.1.34 RAID1(12TB IronWolf x 2)
Re: Emule and Calibre
emule exists in synology and qnap, therefore, there is some version or way to configure emule over nas / linux
F2-221
Re: Emule and Calibre
qBittorrent for TOS will be online soon. I think this is what you need.
To contact our team, please send email to following addresses, remember to replace (at) with @:
Support team: support(at)terra-master.com (for technical support only)
Service team: service(at)terra-master.com (for purchasing, return, replacement, RMA service)
Support team: support(at)terra-master.com (for technical support only)
Service team: service(at)terra-master.com (for purchasing, return, replacement, RMA service)
Re: Emule and Calibre
the program you looking for is called amule. is like emule but for linux systems
Re: Emule and Calibre
Ciao all,
there are news about amule for F2-422 ?
It is the only Intel NAS doesn't offer amule ......
EU
there are news about amule for F2-422 ?
It is the only Intel NAS doesn't offer amule ......
EU
- infoaliste
- Posts: 20
- Joined: 29 Nov 2020, 17:53
Re: Emule and Calibre
Hi, I have managed to install emule on my F2-221. TOS 4.2.06 If you want to try these are the steps I have followed:
First, I installed Docker from the TOS application installer.
Then I log in SSH as root and execute the following command to install the container:
After a couple of minutes, emule is ready and we can open the browser and manage emule through the IP of your NAS port 4711 (http://yournasip:4711)
Password: admin
You can now leave the SSH session.
If you want to pause the container, log back into SSH and run the following command:
To reactivate it:
Remember that for emule to work properly you must open the following ports on your router:
23732 TCP
23733 UDP
If you want to manage emule from outside your local network you must also open port 4711
In my installation, I find the downloads in the following route:
/mnt/md0/appdata/docker/volumes/emule_data/_data/download
This path may change in your installation depending on the configuration of your storage system
More information about the emule container installed:
https://github.com/tokkenno/emule-docker
First, I installed Docker from the TOS application installer.
Then I log in SSH as root and execute the following command to install the container:
Code: Select all
docker run -p 4711:4711 -p 23732:23732 -p 23733:23733 -v emule_data:/data --name emule reimashi/emule
Password: admin
You can now leave the SSH session.
If you want to pause the container, log back into SSH and run the following command:
Code: Select all
docker pause emule
Code: Select all
docker unpause emule
23732 TCP
23733 UDP
If you want to manage emule from outside your local network you must also open port 4711
In my installation, I find the downloads in the following route:
/mnt/md0/appdata/docker/volumes/emule_data/_data/download
This path may change in your installation depending on the configuration of your storage system
More information about the emule container installed:
https://github.com/tokkenno/emule-docker
-
- Posts: 20
- Joined: 28 Feb 2020, 17:31
Re: Emule and Calibre
Hi all,
can you tell me how can I share my folders with this tokkenno emule docker version?
can you tell me how can I share my folders with this tokkenno emule docker version?
- infoaliste
- Posts: 20
- Joined: 29 Nov 2020, 17:53
Re: Emule and Calibre
As far as I know, the shared folder is the same one where the downloads are made: ...emule_data/_data/download.
I don't know if more folders can be added for sharing
I don't know if more folders can be added for sharing